Updated November 2026

Installing solar panels on a tiled roof is possible, but the tiles are the part that can go wrong. This guide walks you through checking your roof, choosing the right mounting approach, and protecting the tiles and underlayment so the system lasts without leaking. Read the whole process before you climb up, because the sequence matters.

Step 1: Check the Roof Structure and Tile Type

Start by confirming the roof can carry the added load. Most residential panels weigh roughly 40 pounds each, plus racking, so a structural check matters. If you are unsure, read our guide on Roof Reinforcement for Solar Panels: How to Assess and Strengthen Your Roof before you buy anything.

Shopping for one? See our guide: Top 3 Solar Panels as Roof Shingles Compared for Homeowners.

Next, identify your tile type. Concrete tiles are heavy and brittle, clay tiles are heavy and can crack under foot traffic, and interlocking tiles are lighter but have shapes that complicate flashing. Your tile type determines which hooks and flashings you will need.

Step 2: Choose a Mounting Method for Tiles

Tiled roofs are almost always mounted with tile hooks or replacement tile flashings. The hook slides under the tile above, hooks onto the batten or rafter, and the rail attaches to the hook. Because the hook penetrates the roof, every penetration needs sealing. For a broader look at hardware options, see Roof Mounting Hardware for Solar Panels: A Step-by-Step Guide for Homeowners.

Keep in mind that mounting height and angle also affect how the array sits on the tiles. The pitch of your roof influences rail spacing and wind loading. Best Angle for Solar Panels on Roof: A Step-by-Step Guide (2026) explains how to think about that.

Step 3: Plan Layout and Locate Rafters

  1. Measure the roof and sketch the panel layout on paper, leaving clearance from the ridge, eaves and edges.
  2. Locate rafters with a stud finder or by measuring from a fixed point. Typical spacing is 16 or 24 inches on center; confirm yours.
  3. Mark hook positions on the tile courses so each hook lands under a full tile and over a rafter.
  4. Confirm the layout with a chalk line before drilling anything.

Step 4: Install Hooks, Flashing and Rails

Remove the tiles at each hook position, install the flashing, set the hook into the rafter with structural screws, and reinstall the tiles around it. Seal the penetration according to the flashing maker’s instructions. Then bolt the rails to the hooks, check that they are level and parallel, and only then clip on the panels. Work carefully: broken tiles are expensive to replace and are a common leak source.

  • Cordless impact driver makes driving structural screws into rafters faster and more consistent. View on Amazon
  • Roofing safety harness kit keeps you secure on a pitched roof. View on Amazon
  • Stud finder helps locate rafters before you mark hook positions. View on Amazon

Common Mistakes to Avoid

  • Mounting hooks into the batten only, rather than the rafter, which can pull out in wind.
  • Cracking tiles by walking on them. Use roof ladders and step on the rafters where possible.
  • Skipping flashing or using sealant as a substitute for proper flashing.
  • Ignoring local permit and inspection rules before starting work.
  • Working alone on a steep roof, especially in wet or windy weather.

FAQ

Can solar panels be installed on any tile roof?

Most tile roofs can accept panels, but heavy or fragile tiles and weak rafters may need reinforcement first. A structural assessment by a qualified professional is a sensible first step.

Do tile hooks cause leaks?

They can if flashed and sealed poorly. Properly installed flashing designed for your tile profile is what prevents water entry.

Should I hire a professional?

Many homeowners do the layout and rail work themselves but hire a licensed roofer or electrician for penetrations and wiring. Check local code requirements before deciding.

Conclusion

Solar panels on a tiled roof come down to three things: a sound structure, correct hooks and flashing, and careful handling of the tiles. Take the time to plan your layout and confirm rafter locations. Check local permit requirements, and consult a licensed professional for structural or electrical work.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.