Updated November 2026

Solar panels on a roof can start a fire, but it is uncommon when the system is designed, wired, and mounted correctly. Most solar panels roof fire incidents trace back to electrical faults, especially DC arcing in connectors, loose terminals, damaged cable insulation, or undersized wiring. Mounting problems and roof penetrations that let water in can make things worse over time.

Why Solar Panel Fires Happen

A rooftop array produces direct current (DC) at voltages that can exceed 400 volts in a typical string. DC arcs do not extinguish on their own the way alternating current does at zero-crossings, so a loose or corroded connection can keep sparking and heating until something ignites. Arc faults are the main concern, and they usually start small.

Shopping for one? See our guide: Top 3 Solar Panels as Roof Shingles Compared for Homeowners.

Other common causes include:

  • Mismatched or non-listed connectors that do not fully seat or lock
  • Cables pinched under mounting rails or rubbed through by wind-driven movement
  • Rodent damage to wire insulation in the attic or conduit run
  • Water getting into junction boxes after a roof penetration was poorly sealed
  • Overheated components from undersized conductors or an inverter running too hot

Factors That Raise or Lower the Risk

Roof age and material matter. A shingle roof near the end of its life can crack or lift, exposing fasteners and wiring to water. Wood-framed roofs with dry, dusty attic spaces make fire spread faster if an arc does start, which is why ventilation and clearance around electrical gear matter. Panels installed flush against a roof with no airflow can also run hotter, which stresses cable jackets and connectors.

Installation quality is the biggest variable. Systems installed by licensed electricians who follow the National Electrical Code (NEC) and the equipment manufacturer’s torque and bend-radius specifications have a much lower risk profile than systems put together without permits or inspection.

What Homeowners Can Do About It

If you already have a system, or you are planning one, these steps reduce the chance of a problem:

  1. Confirm the installer used listed components and pulled the required permits.
  2. Ask whether the system has DC arc-fault protection, which is required in many jurisdictions under current NEC rules.
  3. Check that the inverter and combiner box have a rapid shutdown device that meets local code.
  4. Have a qualified electrician inspect connectors, torque on terminals, and cable routing once a year.
  5. Look at the roof and attic after storms for chafed wires, loose clips, or water stains near penetrations.
  6. Keep vegetation, leaves, and debris off the array and out of gutters beneath it.
  7. Monitor your system output. A sudden drop can signal a failing string before it becomes a hazard.

For background on keeping a roof-mounted array sound, see Solar Panels on Roof Problems: 6 Issues to Check and Fix and Solar Panels on Tiled Roof: A Step-by-Step Guide for Homeowners. If your roof is near the end of its life, Mounting Kits to Install Solar Panels on Old Roofs is worth reviewing before you add anything new.

What We’d Use

A dedicated thermal or infrared camera is useful for spotting hot connectors during an inspection, since overheating often shows up before a failure. View on Amazon

Weather-rated cable clips and UV-resistant wire management fittings help keep DC runs off the roof surface and away from sharp edges. View on Amazon

FAQ

Are solar panels on a roof a common cause of house fires?

No. Fires linked to rooftop solar are rare compared with the number of installed systems. Most cases involve wiring faults or poor installation, which code requirements and inspections are designed to catch.

Do I need DC arc-fault protection on my system?

Many local codes require it for newer installations. Check with your permitting office or installer, since requirements vary by jurisdiction and by the NEC edition adopted locally.

What should I do if I smell burning or see scorch marks?

Turn off the system at the inverter and main service disconnect if it is safe to do so, then call a licensed electrician or your fire department. Do not touch damaged wiring or panels yourself. Consult a qualified professional for any electrical inspection or repair.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.