Updated November 2026

Roof repairs with solar panels take more planning than a standard patch job, but they are manageable if you work in the right order. This guide walks you through assessing the damage, safely removing and reinstalling the array, and sealing the roof so leaks don’t return. You’ll also learn when the job is better handed to a licensed professional.

Assess the Damage Before Touching the Array

Start by determining where the leak or damage actually is. Water often travels along rafters or under flashing before it appears on your ceiling, so the stain may be several feet from the source. Check for cracked or lifted shingles, exposed nail heads, deteriorated sealant around mounting feet, and damaged flashing at the edges of the array. Photograph everything before you disturb it. These photos help with insurance claims and with your installer’s warranty review.

Shopping for one? See our guide: Solar Panel System for Home Installation: 6 Best Options Compared (2026).

Also review your panel documentation and mounting system manual. Some racking manufacturers specify exact torque values and required lift points, and a repair that ignores them can void your workmanship warranty.

Remove and Store Panels Safely

Only disconnect panels when the system is fully de-energized. Turn off the inverter and any DC disconnect, then confirm with a meter that the string voltage is near zero before unplugging MC4 connectors. Keep connectors clean and dry, and cap any exposed plugs.

Lifting modules is the most common source of injury on these jobs. Use two people per panel, wear gloves, and carry panels on their edges rather than by the frame corners. Store them flat or leaning on padded supports in a dry place, face up, away from foot traffic. Panels are heavy and glass cracks easily, so never stack them on uneven ground.

Repair the Roof Underneath

With the array off, you can work on the roof directly. Replace damaged shingles and check the underlayment beneath. Pay particular attention to the penetrations where mounting hardware passes through the roof surface, because these are the most likely leak points.

Re-flash Each Mount Point

  1. Lift the shingle courses above and beside each mount.
  2. Inspect the flashing and replace it if it is cracked, corroded or warped.
  3. Seat new flashing so each upper course overlaps it, shingle-style, so water runs over rather than under.
  4. Seal exposed fasteners with a compatible roofing sealant, and confirm the sealant type is approved for the roofing material.

Reinstall the Array and Verify Connections

Reattach the racking to the rails at the same points, using the torque specification in the racking manual. Reconnect the modules in the original string order, then check polarity and open-circuit voltage at the combiner before powering up. Restart the inverter only after the string readings match what you recorded before removal. If anything looks off, stop and recheck the wiring.

Common Mistakes

  • Lifting panels by the junction box or cables, which can damage internal components.
  • Skipping the flashing and relying on sealant alone, which often fails within a few seasons.
  • Tightening mounts beyond the specified torque, which can crack modules.
  • Working on a wet or icy roof, a serious fall risk.
  • Reconnecting strings in a different order without recording the original layout.
  • Digital multimeter: confirms the system is de-energized and checks string voltage before and after reconnection. View on Amazon
  • Roofing sealant rated for your roof type: seals flashing and fasteners without trapping moisture. View on Amazon
  • MC4 disconnect tool: separates locked connectors without damaging them. View on Amazon

FAQ

Do I need to remove the solar panels to fix my roof?

Usually yes, at least for the area under the array, because you cannot properly inspect or replace shingles and flashing beneath modules. Small repairs at the edges sometimes allow you to work around the racking.

Will roof repairs affect my solar warranty?

They can if the work damages equipment or ignores the manufacturer’s mounting specifications. Keep records of every step and check your installer’s warranty terms before starting.

Should I hire a professional for this job?

If the roof is steep, the damage is extensive, or the array is large, a licensed roofer and a certified solar installer are the safer choice. Consult a qualified professional for structural concerns or any electrical work you are unsure about.

Conclusion

Successful roof repairs with solar panels depend on careful damage assessment, safe panel handling, and proper re-flashing at every mount. Work in the right sequence, follow the racking torque specs, and verify the electrical connections before restarting the system. When in doubt about structure or wiring, bring in a professional.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.