Updated November 2026

To make a battery bank for solar panels, you size the bank to your daily energy use, choose matching batteries, wire them in the correct series and parallel arrangement, and connect them to your solar charge controller through proper fusing. The result is a storage system that keeps your lights, fridge and electronics running when the sun goes down or the grid fails. Most of the work is in the planning, so take your time with the numbers before you buy anything.

Step 1: Calculate Your Daily Energy Needs

Start by listing every device you plan to run from the battery bank. Look at each label or the manufacturer’s spec sheet for wattage, then estimate how many hours per day it runs. Multiply watts by hours to get watt-hours (Wh), and add them up.

Shopping for one? See our guide: Solar Panel System for Home Installation: 6 Best Options Compared (2026).

For example, a 60-watt LED light running 5 hours uses 300 Wh. A 50-watt router running 24 hours uses 1,200 Wh. Your total is the number you size the bank around.

Next, account for losses. Inverters and wiring typically lose 10 to 20 percent, so multiply your daily total by about 1.2. Then decide how many days of backup you want. Two days of autonomy is a common starting point for a home setup.

Step 2: Choose Your Battery Type and Voltage

Lithium iron phosphate (LiFePO4) batteries are the most common choice for home battery banks today. They tolerate deeper discharge, last more cycles than lead-acid, and need less maintenance. Lead-acid batteries, including flooded and AGM types, cost less upfront but deliver less usable capacity and wear out faster when regularly drained.

Pick a system voltage that matches your inverter and charge controller, usually 12V, 24V or 48V. Higher voltage means lower current for the same power, which allows thinner wire and less heat. Always use batteries of the same type, capacity and age in one bank.

Step 3: Wire the Batteries Correctly

Connecting batteries in series adds voltage while keeping capacity the same. Connecting them in parallel adds capacity while keeping voltage the same. For example, four 12V 100Ah batteries wired in series-parallel (two strings of two in series, joined in parallel) give 24V at 200Ah.

Follow this sequence:

  1. Confirm all batteries read the same voltage before connecting them.
  2. Use a battery-rated bus bar or short, equal-length cables so current splits evenly.
  3. Tighten terminals to the torque value in the battery manual.
  4. Install a fuse or breaker on the positive lead close to the battery, rated for the maximum current.
  5. Connect the bank to the charge controller and inverter last, with a disconnect switch between them.

Step 4: Set Up Charging and Protection

Your solar charge controller must match the battery chemistry. An MPPT controller set to a LiFePO4 charge profile is a reliable choice. Program the absorption and float voltages from the battery manufacturer’s datasheet rather than relying on factory defaults.

Add a battery management system (BMS) if your batteries do not include one. A BMS guards against overcharge, over-discharge, short circuits and cell imbalance. Mount the bank in a ventilated, temperature-stable location, and keep it out of living spaces. Lithium batteries should not be charged below freezing unless the battery has built-in heating.

Because battery banks store a lot of energy, electrical work at this scale carries real risk. If you are unsure about any connection, consult a licensed electrician before energizing the system.

Common Mistakes to Avoid

  • Mixing old and new batteries, or different capacities, in the same bank.
  • Undersizing wire, which causes voltage drop and overheating.
  • Skipping fuses or using a fuse rated far above the wire’s safe current.
  • Using a lead-acid charge profile on lithium batteries, which can shorten their life.
  • Ignoring ventilation and temperature limits in the storage area.
  • Victron Energy SmartShunt helps you track state of charge accurately, which makes it easier to know when your bank is low. View on Amazon
  • Victron Energy SmartSolar MPPT charge controller is widely used for matching solar input to lithium battery banks. View on Amazon
  • Battery bus bar kit keeps parallel connections equal in length and current, which reduces imbalance. View on Amazon

FAQ

How big should my battery bank be?

Size it by multiplying your daily watt-hour use by the number of backup days you want, then adding about 20 percent for losses. Only draw down lithium batteries to their recommended depth of discharge.

Can I mix lithium and lead-acid batteries?

No. They have different charge voltages and behavior, so mixing them can damage both. Keep one battery chemistry per bank.

Do I need a professional to install a battery bank?

Many homeowners handle the wiring themselves, but a licensed electrician should review the design, especially for connections to the home’s main panel. Check local permit requirements before installing. For a deeper look, 6 Best Solar Panel Battery Wiring Diagram Guides for Homeowners (2026) covers this in detail.

Conclusion

A well-built battery bank starts with an honest energy count, followed by careful battery selection and clean, fused wiring. Matching your charge controller to the battery chemistry protects your investment for years. Take the planning seriously, and you will end up with backup power you can rely on.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.