Updated November 2026

Roof pitches that work well with solar panels are generally between about 15 and 40 degrees, with the sweet spot for most US homes landing near 30 to 35 degrees. This guide explains why those numbers matter, how to measure your own roof, and how pitch interacts with direction, shading and mounting hardware. By the end, you will know whether your roof is a good candidate and what to change if it is not.

Why Roof Pitch Matters for Solar Output

Solar panels produce the most energy when they face the sun as directly as possible. Pitch is the angle of the roof surface measured from horizontal, so it controls how squarely panels meet the sun’s rays across the day and across the seasons. A flat surface receives sunlight at a shallow angle in winter and a steep one in summer, while a moderate pitch balances the two.

Shopping for one? See our guide: Do Solar Panels Work on North Facing Roof? 4 Best Picks Compared (2026).

For a fixed system, most installers aim for a tilt roughly equal to your latitude, give or take 10 to 15 degrees, depending on whether you want more winter or summer production. In much of the continental US, that puts the ideal tilt somewhere between 25 and 40 degrees. Your roof does not need to match that exactly. Being close is usually good enough, and the difference between a 25-degree and a 35-degree roof is often smaller than the effect of a single tree casting a shadow.

Pitch Ranges That Work Well

Use the following ranges as a starting point. They describe general performance patterns, not guaranteed output, because local weather, shading and panel quality all matter.

Roof pitch (degrees) Typical rise per 12 inches Suitability for solar
0 to 5 Under 1 inch Workable with tilt racking; drainage and wind loads need extra attention
6 to 14 1 to 2 1/2 inches Acceptable; panels may be laid nearly flat with some output loss
15 to 25 3 to 5 1/2 inches Good; standard racking works well
26 to 40 5 3/4 to 10 inches Ideal range for most mounting systems
41 to 50 10 1/4 to 14 inches Still productive; wind uplift and access may be concerns
Over 50 Over 14 inches Steep roofs are harder to access; installers may use special hardware

A pitch in the 15 to 40 degree band usually gives the best combination of energy output, standard mounting options and reasonable installation labor. Above that, the roof is still usable but the job becomes more demanding. Below about 10 degrees, you will typically need ballasted or tilted racks, which add parts and wind-load design work.

How to Measure Your Roof Pitch

You do not need to climb onto the roof to find its pitch. Several methods work.

Method 1: Use a Level and a Tape Measure

  1. Hold a 12-inch level flat against the roof surface, from the eave toward the ridge.
  2. Keep the level horizontal and measure the vertical gap between the bottom of the level and the roof at the far end.
  3. That gap, in inches, is your rise per 12 inches. Look it up in the table above or use a roof pitch calculator.

Method 2: Use a Smartphone App

Several inclinometer apps read tilt from your phone’s accelerometer. Place the phone flat against a shingle course, record the reading, and repeat in a few spots to confirm it is consistent.

Method 3: Check the Roof Plans or Permit Records

If the home was built or re-roofed under a permit, the original drawings may list the pitch. Your installer can also pull this from aerial imagery during a site survey.

Factors Beyond Pitch That Affect Performance

Pitch is only one part of the picture. Direction, shading and roof condition often matter as much.

Roof Direction

In the Northern Hemisphere, south-facing roofs usually produce the most energy, followed by southwest and southeast. East and west roofs still generate well, often producing a more even curve across the day that can suit time-of-use rates. North-facing roofs are the hardest to justify. Check the article on whether solar panels work on north-facing roofs for specifics on when that orientation still makes sense.

Shading

A shaded panel can drag down the output of its entire string, so shading deserves more attention than a few degrees of tilt. Trees, chimneys, dormers and neighboring buildings all count. Installers typically use a shade analysis tool or a sun-path device during the site visit to map shade hours across the year.

Roof Shape

Hip roofs, which slope on all four sides, can create awkward layouts because each face has a different direction and pitch. Gable roofs usually give the cleanest, most uniform layout. Complex roofs with many valleys can still work, but they often need smaller arrays on specific faces.

Roof Age and Material

If the roof has less than about 10 to 15 years of life left, consider replacing it before installing panels. Removing and reinstalling an array later costs labor and risks damage. Metal, asphalt shingle, tile and composite roofing each use different mounting hardware, so the material affects the attachment method as much as the pitch does.

Step-by-Step: Checking Your Roof Before You Buy

  1. Measure the pitch of each roof face you might use.
  2. Note the compass direction of each face. A phone compass app works fine for a rough reading.
  3. Walk the property at different times of day and note trees, vents and nearby structures that cast shade.
  4. Identify the largest unshaded area on the roof that fits your target system size.
  5. Check the roof’s age and condition, including flashing, shingle wear and any sagging.
  6. Ask two or three installers for a site survey and compare their layout and shade results.

Tools and Supplies to Have on Hand

  • A 12-inch level and a 25-foot tape measure
  • A smartphone with an inclinometer and compass app
  • A notepad or spreadsheet for measurements and shade observations
  • Binoculars for inspecting the roof from the ground
  • A camera or drone (if permitted and used safely) to capture the full roof layout

Common Mistakes

  • Ignoring shade because the roof pitch looks perfect. A perfect angle does not help if a chimney shades one corner every afternoon.
  • Measuring on the wrong face. Hip and complex roofs have several pitches. Measure each face separately.
  • Assuming steep roofs are always better. Beyond about 40 degrees, the energy gain is small while installation and wind-load costs climb.
  • Installing on an aging roof. Replacing the roof after panels are up means paying twice for labor.
  • Skipping a structural check. Older rafters may need reinforcement, especially for heavier systems on low-slope roofs.

Tips for a Better Result

  • If your best face is slightly off-ideal, a few extra panels often recover the lost output.
  • Consider microinverters or power optimizers on roofs with mixed orientations or partial shade, since they limit the impact of one underperforming panel.
  • Ask installers to model production for your exact roof, not just a generic estimate.
  • Photograph the roof from several angles before work starts so you have a record of its condition.

FAQ

What is the best roof pitch for solar panels?

Most mounting systems perform well between about 15 and 40 degrees, with roughly 30 to 35 degrees often ideal in the middle of the US. Your local latitude and seasonal goals can shift the best value.

Can solar panels go on a flat roof?

Yes. Flat roofs use tilt racks or ballasted mounts to set panels at an angle, usually around 10 to 15 degrees. These systems need careful wind-load design and roof drainage planning.

Does a steep roof produce more energy?

Not necessarily. Once the pitch passes roughly 40 degrees, the extra gain is modest, and installation can become harder and more expensive.

Is a north-facing roof with the right pitch usable?

It can be, though output is typically lower. Whether it is worth installing depends on your site, your electricity use and your local net metering rules.

How do I know if my roof pitch is too low?

Measure it with a level or app. If it reads under about 10 degrees, expect to use tilt racking or a ballasted system, and ask an installer to confirm the design.

Does roof pitch affect panel cleaning?

Yes. Steeper roofs shed rain and debris more easily, while very low pitches may collect dust and bird droppings. Plan cleaning access either way.

Should I consult a professional before installing?

Yes. A licensed installer or structural engineer should verify roof load capacity, attachment methods and electrical connections. Electrical and structural work carries real safety risk, so consult a professional before you proceed.

Conclusion

Roof pitches between about 15 and 40 degrees work well for most solar installations, with the middle of that range offering the best balance of output and simple mounting. Measure each roof face, check its direction and shade, and confirm the roof is in good condition before committing. When in doubt, get a detailed site survey from a qualified installer.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.