Updated November 2026

If your roof splits into an east-facing slope and a west-facing slope, you can still run a capable solar array on your home. Solar panels on an east west facing roof produce power across most of the day instead of peaking at midday, and that shift can work well with how your household actually uses electricity. This guide walks you through checking your roof, planning the layout, and avoiding the mistakes that cost output.

Understand How East and West Slopes Produce Power

An east-facing panel catches the morning sun first and tapers off by early afternoon. A west-facing panel starts slow and peaks in the late afternoon. Together, the two slopes produce a broader curve than a single south-facing array, which often gives a flatter output profile through the day. Output on each slope is typically lower at peak than a south-facing array of the same size, so expect a smaller daily total per panel. Your installer or a solar design tool can model the difference for your exact roof and location.

Shopping for one? See our guide: Top 3 Solar Panels as Roof Shingles Compared for Homeowners.

Measure Your Roof and Plan the Layout

Start by measuring each slope in feet, then convert to usable area. Leave clearance from the roof edges and ridge, and account for any vents, chimneys or skylights that block a panel footprint. If you want more background, see Solar Panels on Sheet Roof: A Step-by-Step Guide for Homeowners.

  1. Measure the length and width of the east slope and the west slope separately.
  2. Note the pitch of each slope using a digital angle finder or a level and a tape.
  3. Mark vents, skylights, satellite mounts and chimneys on a sketch of the roof.
  4. Subtract a clear margin from every edge, commonly around 18 inches at the ridge and eaves, though your local fire code may specify more.
  5. Sketch panel rows that fit each slope, keeping panels in clean rectangles.
  6. Check the panel dimensions from your chosen manufacturer’s datasheet against your sketch.

Check Structure, Shade and Wiring Paths

Before you order panels, confirm the roof framing can carry the added load. Most manufacturers specify a maximum distributed load per panel, and a licensed structural engineer or your installer can verify rafter size and spacing. Trees and neighboring buildings matter just as much. Shade on the morning slope or the evening slope affects its output more than you might expect, so observe the roof at different times of day for a few days.

Plan the wiring path early. Each slope usually feeds its own string or its own microinverter set, so the two arrays may need separate roof penetrations and conduit runs. Ask your installer whether string inverters, microinverters or power optimizers suit a split-facing layout, since per-panel electronics can reduce losses when orientations differ. Worth reading next: Solar Panels North East Facing Roof: What to Expect and How to Plan.

Compare Your Options and Get Permits

Once your layout is drafted, compare how the array will meet your household load. An east-west split often suits homes where people are active in the morning and evening. Check your utility’s net metering rules, because some utilities treat each array differently and interconnection requires an application. Permit requirements, inspection timelines and required setbacks vary by city and county, so check with your local building department before installation. Electrical and structural work should be done by qualified professionals.

Common Mistakes

  • Assuming an east-west array will match a south-facing one kilowatt for kilowatt.
  • Skipping the shade study and discovering a chimney shadow after installation.
  • Forgetting fire-setback clearances when sketching panel rows.
  • Choosing string inverters without checking how mixed orientations affect output.
  • Ignoring roof age, since replacing a worn roof after panels are mounted is costly and disruptive.
  • Digital angle finder: A quick way to record the pitch of each slope accurately during planning. View on Amazon
  • Laser distance measurer: Speeds up measuring long roof slopes and clearance distances from the eaves and ridge. View on Amazon
  • Roof sketch and planning notebook kit: Helps you record measurements and layout ideas while you walk the roof with an installer. View on Amazon

FAQ

Are east west facing solar panels worth it?

They can be, especially if your household uses more power in the morning and evening. Output per panel is usually lower than a south-facing array, so compare total production and your utility’s rates before deciding.

Do I need separate inverters for each slope?

Not always. String inverters can work if both slopes are wired into separate strings, while microinverters or optimizers handle mixed orientations per panel. Ask your installer which setup fits your roof.

Can I install panels on both slopes at once?

Yes, many homes do. Confirm structural capacity, clearances and permit requirements for both slopes, and have a licensed professional handle the electrical connections.

Conclusion

Solar panels on an east west facing roof trade some peak output for a longer, more even production curve. Measure each slope, check structure and shade, and plan wiring before you buy. Confirm permits and utility rules with local authorities and have qualified professionals handle the electrical and structural work.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.