Updated November 2026

Solar panel to house wiring is the path that moves electricity from your roof array through combiner boxes and an inverter, then into your home’s main electrical panel. This guide explains each stage, the parts involved, and the points where a licensed electrician should take over. By the end, you will understand how a typical residential system is wired and what questions to ask before any work begins.

How the Wiring Path Works

Panels produce direct current (DC), which your home cannot use. The wiring carries that DC power down the roof, into an inverter that converts it to alternating current (AC), and then into your house. Each stage has its own wire type, protection devices, and code requirements.

Shopping for one? See our guide: Solar Panel System for Home Installation: 6 Best Options Compared (2026).

  • Module wiring: Panels connect to each other in series strings using pre-terminated MC4 connectors.
  • Home run: Strings run to a combiner or disconnect box, usually through conduit.
  • Inverter: The DC side feeds the inverter, and the AC side leaves it.
  • Service connection: AC output connects to the main panel through a dedicated breaker.

Step-by-Step: From Roof to Main Panel

1. Plan string layout and wire sizing

Your installer or designer calculates how many panels go into each string, based on the inverter’s voltage window. Wire gauge depends on current and distance, and voltage drop should stay low. Manufacturers of inverters publish these limits, so check the datasheet before buying cable.

2. Run and protect the DC wiring

Use UV-rated, double-insulated PV wire from the panels to the combiner. Secure it with clips rated for outdoor use and keep it off sharp edges. Install DC disconnects and overcurrent protection where the code requires them.

3. Connect the inverter

Mount the inverter in a shaded, ventilated spot close to the main panel. Terminate DC conductors per the inverter manual, then wire the AC output to a breaker sized for the inverter’s rated output current.

4. Tie into the main panel

Most homes use a dedicated breaker in the main panel. This is the most important connection in the system. Lock out power before working inside the panel, and confirm the utility interconnection requirements before your system is switched on. If your area uses net metering, your utility may require a bidirectional meter; see What Is Net Metering for Solar Panels? A Homeowner's Plain-English Guide for how that works.

Wire Sizing and Conduit Checklist

Use this checklist before scheduling inspection:

  1. String voltage calculated at the coldest expected temperature.
  2. Conductor ampacity matched to the protective device and temperature derating.
  3. Conduit fill and bend count within code limits.
  4. Labels at every disconnect, combiner, and inverter.
  5. Grounding and bonding completed for the array and racking.
  6. Rapid shutdown device installed where required.

Common Mistakes

  • Using indoor-rated wire outdoors, which can crack in sunlight.
  • Undersizing conductors to save money, causing heat and voltage drop.
  • Skipping labels, which slows inspection and future service.
  • Mounting the inverter in a hot attic with no airflow.
  • Backfeeding the main panel through an undersized breaker.

If you have questions about your roof layout or cable routing, see Solar Panels on Residential Roof: 3 Best Picks Compared for Homeowners and Solar Panels on Roof Problems: 6 Issues to Check and Fix for related considerations.

  • Multimeter with DC voltage range: Verifies string voltage and polarity before connecting anything. View on Amazon
  • MC4 crimping tool: Gives clean, rated crimps on pre-terminated connectors. View on Amazon
  • Insulated hand tool set: Reduces the risk of accidental shorts when working near energized conductors. View on Amazon

FAQ

Can I run solar panel to house wiring myself?

Some homeowners handle mounting and module wiring, but main panel connections and utility interconnection usually require a licensed electrician and a permit. Check your local rules first.

What wire type is used on the roof?

Installers typically use PV-rated, UV-resistant, double-insulated cable designed for outdoor exposure and high DC voltages. Confirm the rating matches your system’s voltage.

Does the inverter go between the panels and the house?

Yes. The inverter converts DC from the panels into AC that your home can use, so it sits between the array and the main panel connection.

Conclusion

Solar panel to house wiring follows a clear path: panels to strings, strings to combiners, combiners to the inverter, and the inverter to a dedicated breaker in the main panel. Careful sizing, protection, and labeling make the system safer and easier to inspect. For final design and permits, consult a licensed solar installer or electrician in your area.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.