Updated November 2026

The best roof orientation for solar panels in the Northern Hemisphere is generally a south-facing roof, with west-facing as a strong second choice. In this guide you will learn how to read your roof’s direction, check tilt and shade, and decide whether your roof is a good candidate for a home solar array.

Why Orientation Affects Solar Output

Panels produce the most electricity when they face the sun for the longest part of the day. In the US, the sun sits low in the southern sky through the winter, so panels facing south catch the most direct light over the year. A south-facing roof typically delivers the highest annual production, while east- and west-facing roofs produce less but spread output across the day, which can suit homes with time-of-use rates.

Shopping for one? See our guide: Solar Panel System for Home Installation: 6 Best Options Compared (2026).

Step 1: Find Your Roof’s Compass Direction

Use a compass app on your phone while standing on the ground below the roof, or check an aerial map that shows north at the top. Note which slope faces the direction you want to measure. Roofs rarely face exactly south, so a slope within about 45 degrees of due south is usually workable. Use these rough guides:

  • South (within 20 degrees): Best overall production.
  • Southeast or southwest: Still strong, with only a small loss in annual output.
  • East or west: Usable, with noticeably lower total production but a longer daily curve.
  • North: Generally a poor choice for panels in the Northern Hemisphere.

Step 2: Check Roof Tilt and Shade

Orientation matters less if the panels are shaded or sit at a bad angle. Most fixed residential arrays perform well with a tilt roughly equal to your latitude, but the roof’s own pitch is often close enough. A pitch between about 15 and 40 degrees works well for most US homes. Next, watch the roof for several sunny hours. Trees, chimneys, neighboring buildings and vent pipes that cast shadows across the panels can cut output sharply, so note any shade between roughly 9 a.m. and 3 p.m.

Shade Check Checklist

  1. Record the compass direction of each roof slope.
  2. Measure the pitch with a level and protractor app.
  3. Photograph the roof at several times of day.
  4. Mark any obstructions that cast shadow on the proposed panel area.
  5. Estimate usable square footage after setbacks and vents.

Step 3: Compare Your Roof to a Quick Reference

The table below gives a general sense of how orientation affects relative output. Actual results depend on your location, climate and shade, so treat these as rough comparisons only.

Roof Direction Relative Annual Output Best Use Case
South Highest Maximum total production
Southeast / Southwest High Strong overall output
East / West Moderate Spreading output across the day
North Lowest Usually avoided

If your roof does not face the ideal direction, your installer may use ground mounts or a second array on another slope. For a broader check of suitability, see Is My Roof Suitable for Solar? Orientation, Shade, Age and Structure.

Step 4: Confirm Structure and Local Rules

Before settling on a layout, confirm that the roof structure, age and covering can support the array, and check local permit and setback requirements. A licensed structural engineer or solar installer can verify load capacity. For planning the wiring and mounting, Roof Solar Panels DIY: A Step-by-Step Guide for Homeowners walks through the basics. Your utility’s net metering rules also affect how you size the system, so review What Is Net Metering for Solar Panels? A Homeowner's Plain-English Guide.

Common Mistakes

  • Choosing a north-facing slope to save a few panels’ worth of space.
  • Ignoring seasonal shade from trees that grow over the years.
  • Measuring orientation with a magnetic compass near metal gutters or vents.
  • Assuming an east-west split always beats a single south array; check your rate structure first.
  • Skipping a structural check on older roofs.
  • Smartphone compass app: Quick way to take a reading on each roof slope before you climb up. View on Amazon
  • Digital angle finder: Measures roof pitch accurately for tilt planning. View on Amazon
  • Solar pathfinder-style shade tool: Helps map shade across a day and season. View on Amazon

FAQ

Is south-facing always the best roof orientation for solar panels?

In most of the US, a south-facing roof produces the most total energy over a year. Shade, pitch and local rate structures can change which orientation makes the most financial sense.

Can I use an east or west roof for solar?

Yes. East and west roofs produce less total energy but more evenly across the day, which can be useful if your utility charges more during evening hours.

Should I hire a professional to check my roof?

Yes, especially for structural and electrical questions. A licensed installer or engineer can confirm load capacity and permit requirements before you buy equipment.

Conclusion

For most homes, a south-facing roof with a reasonable pitch and little shade gives the best results. Check your compass direction, measure tilt, and map shade across the day before deciding. If your roof falls short, consider east or west slopes or ground mounts, and confirm structural and permit details with a professional.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.