Updated November 2026
Most problems with solar panels on a roof come from a short list of causes: shading, mounting failures, water intrusion, wiring faults, dirt, inverter trouble and aging components. This guide walks you through how to spot each issue, what it usually looks like, and what you can safely check yourself before calling a professional.
Check Your Production Numbers First
The fastest way to catch a problem is to compare your system’s output against what it should be producing. Most inverters and monitoring apps show daily and monthly energy totals. If one month drops sharply compared with the same month the year before, something has changed. Seasonal swings are normal, so compare like months rather than summer against winter.
Shopping for one? See our guide: Solar Panel System for Home Installation: 6 Best Options Compared (2026).
A single panel producing noticeably less than its neighbors often points to shading, a bad connector or a failing module. Whole-system drops usually point to the inverter, a utility outage or a grid-side issue.
Shading and Obstructions
Shade is the most common cause of underperformance. Even a small shadow from a chimney, vent pipe, tree branch or nearby antenna can reduce output from an entire string, because series-wired panels are limited by the weakest module.
- Watch the array at different times of day for a week or two and note which panels go dark first.
- Trim branches that overhang the roof, especially on the south or west side in the Northern Hemisphere.
- Consider microinverters or power optimizers if shading is unavoidable, since they limit the impact to individual panels.
Mounting, Leaks and Physical Damage
Roof-mounted systems put steel, aluminum and penetrating fasteners through your roofing. Over time, these can loosen, corrode or let water in. Check the following from the ground with binoculars, and from the roof only if you can do so safely:
- Look for panels that sit higher or lower than their neighbors, which can signal a lifted or shifted rail.
- Check for cracked glass, delaminated backsheets or browning around the edges of cells.
- Look inside the attic for water stains, soft decking or drip marks near rafters under each mount point.
- Confirm that flashing and sealant around each lag bolt or standoff are intact.
Any sign of water entry should be addressed quickly, because slow leaks can rot roof sheathing before you notice surface damage. Consult a licensed roofer or solar installer for repairs.
Wiring, Connectors and Electrical Faults
Wiring problems are both a performance issue and a safety issue. Loose MC4 connectors, cracked insulation and corroded junction box contacts can cause heat buildup and arcing. Signs include a burning smell, discolored connectors, flickering output or a breaker that trips repeatedly.
Do not open junction boxes or disconnect live strings yourself. Solar DC circuits can carry high voltage even in daylight. Have a qualified electrician inspect the wiring, and make sure the system is properly grounded and labeled.
Dirt, Snow and Debris
Dust, pollen, bird droppings and leaves reduce output, and the effect is often uneven across the array. Snow can block a full row until it slides off. Rinse panels with plain water when the weather is mild and avoid high-pressure washers, which can force water under seals. Do not walk on panels to clean them.
Inverter and Monitoring Problems
If your panels seem fine but production is still low, the inverter may be at fault. Check its display for fault codes, and confirm that it has grid power and is not in standby. Many inverters log error codes that you can look up in the manufacturer’s manual. Repeated faults usually mean the unit needs service or replacement.
Common Mistakes to Avoid
- Ignoring a gradual output decline because it happens slowly.
- Assuming a dark panel is dead without checking for shade or a loose connector first.
- Cleaning panels with abrasive pads or pressure washers.
- Walking on the array or working on the roof in wet or icy conditions.
- Skipping a roof inspection after storms, hail or high winds.
Recommended Gear
A basic multimeter lets you check open-circuit voltage at each string, which helps confirm whether a panel or connector is failing. View on Amazon
A telescoping soft-bristle brush makes ground-level cleaning easier and keeps you off the roof. View on Amazon
FAQ
How often should I inspect my rooftop solar system?
Check production monthly through your monitoring app and do a visual inspection from the ground twice a year. Inspect again after any major storm.
Can I fix a panel problem myself?
Visual checks, cleaning and trimming nearby vegetation are reasonable DIY tasks. Wiring, inverter repairs and roof penetrations should be handled by a licensed professional.
Will a leak from my solar mount void my roof warranty?
It can, depending on the roofer’s and installer’s warranty terms. Review your paperwork and contact both companies promptly if you see water entry.
Conclusion
Most issues with solar panels on a roof show up first as lower production, so tracking your output is the best early warning. Address shading and dirt yourself, and bring in a qualified installer or electrician for mounting, leaks and wiring. Acting early keeps small faults from becoming expensive repairs.
