Updated November 2026

Solar panels do not have to sit on your roof. Ground mounts, pole mounts, carport structures, and balcony or fence-style racks all work for many homes, especially when the roof is shaded, too small, too old, or the wrong direction. This guide walks through the main options and the steps for choosing and planning one.

Why Choose Solar Panels Not Roof Mounted?

A roof is not always the best place for a solar array. Trees may shade it, the pitch or orientation may be poor, or the structure may need repairs first. A separate mount lets you set the angle and direction yourself, and it keeps the work away from your shingles. If you are still deciding whether your roof is a good candidate, the guide on Best Roof Direction for Solar Panels: South-Facing Roofs Win (2026 Guide) explains how orientation affects output.

Shopping for one? See our guide: Top 3 Solar Panels as Roof Shingles Compared for Homeowners.

Step 1: Pick the Mounting Style

Most non-roof setups fall into a few categories:

  • Ground mount: Racks anchored in concrete footings or driven posts. Easy to angle and service, but it needs open yard space.
  • Pole mount: A single post or pair of posts with a tilting frame. Useful for small lots, though wind loads are higher.
  • Carport or pergola: Panels on a freestanding structure that also shades cars or a patio.
  • Balcony or fence rack: Lightweight frames for limited space, usually with fewer panels.

Step 2: Check the Site

Walk the spot at different times of day and note shading from trees, buildings, and fences. Panels should face roughly south in the Northern Hemisphere and get direct sun for most of the day. Measure the available footprint: a typical residential panel is around 65 to 80 inches long and 39 to 40 inches wide, so plan spacing for rows and walkways. For tilt, many installers start near your latitude; the article Best Angle for Solar Panels on Roof: A Step-by-Step Guide (2026) covers the math, which applies to ground and pole mounts too.

Step 3: Plan the Foundation and Structure

Ground and pole mounts depend on the soil and frame. Dig test holes to see how deep the ground is firm, and check for buried utility lines before you dig anywhere, which in the US means calling 811. Frames must resist wind and snow loads for your area, so use hardware rated for those loads and confirm local requirements with your building department. Keep the wiring run short and protected, using conduit rated for outdoor and buried use where required.

Step 4: Wire and Connect Safely

Once the frame is set, mount the panels and run the DC wiring to an inverter. Use UV-resistant cable, keep connections dry, and install a disconnect and overcurrent protection as your local code requires. Because a separate array adds distance and wiring losses, a licensed electrician should review the design, and your utility will need to approve any grid connection before the system is switched on.

Installation Checklist

  1. Confirm sun exposure and shading across seasons.
  2. Measure the footprint and set row spacing.
  3. Check soil, frost depth, and buried utilities.
  4. Choose a frame rated for local wind and snow loads.
  5. Plan conduit, disconnects, and protection with a professional.
  6. Apply for permits and utility interconnection before installing.

Common Mistakes

  • Placing panels where a future tree or building will cast shadow.
  • Skipping the frost-depth check, which can heave footings over time.
  • Using standard indoor-rated wire outdoors.
  • Ignoring wind loads on tall pole mounts.
  • Starting work before permits and utility approval.

A basic digging and layout kit helps you set footings accurately. A multimeter lets you check string voltage before connecting to the inverter.

FAQ

Are ground-mounted solar panels better than roof panels?

They can be, because you control the tilt and direction and avoid roof shading. They do need more yard space and a stronger foundation than a roof array.

Do I need a permit for a ground or pole mount?

In most areas, yes. Permit rules vary by city and county, so check with your local building department before you start.

Can I install a non-roof system myself?

Mechanical work may be manageable, but wiring and utility connection usually require a licensed electrician. Consult a professional for anything involving your electrical service.

Conclusion

Solar panels not roof mounted are a practical choice when your roof is shaded, poorly oriented, or not ready for a system. Pick a mounting style that fits your site, plan the foundation for local loads, and bring in a licensed electrician and your utility early. If you are weighing a roof replacement at the same time, see Roof Replacement With Solar Panels Cost: What to Plan For.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our home solar guides, checking product details against manufacturer specifications and owner feedback.